Latest 100-101 Exam Dumps Cisco Exam from Training Expert VCETorrent
Pass Cisco Meta Certified Digital Marketing Associate PDF Dumps | Recently Updated 83 Questions
NEW QUESTION 44
What does a host on an Ethernet network do when it is creating a frame and it does not have the destination address?
- A. sends out a Layer 3 broadcast message
- B. sends out an ARP request with the destination IP address
- C. drops the frame
- D. sends a message to the router requesting the address
Answer: B
Explanation:
In this case, it will send out an ARP request for MAC address of the destination IP (assuming it doesn't already have it in its table) and then address it to the destination's MAC address.
NEW QUESTION 45
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
R1 does not form an OSPF neighbor adjacency with R2. Which option would fix the issue?
- A. R1 ethernetO/1 is shutdown. Configure no shutdown command.
- B. R2 ethernetO/1 and R3 ethernetO/O are configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
- C. Enable OSPF for R1 ethernetO/1; configure ip ospf 1 area 0 command under ethernetO/1
- D. R1 ethernetO/1 configured with a non-default OSPF hello interval of 25: configure no ip ospf hello-interval 25
Answer: D
Explanation:
Looking at the configuration of R1, we see that R1 is configured with a hello interval of 25 on interface Ethernet 0/1 while R2 is left with the default of 10 (not configured).
NEW QUESTION 46
What are two common TCP applications? (Choose two.)
- A. SNMP
- B. SMTP
- C. FTP
- D. DNS
- E. TFTP
Answer: B,C
Explanation:
SMTP uses TCP port 25, while FTP uses TCP ports 20 and 21.
NEW QUESTION 47
CORRECT TEXT
There are three locations in a school district of a large city: ROUTER -M, ROUTER -W and ROUTER -U. The network connection between two of these locations has already functioned. Configure the ROUTER -M router IP addresses on the E0 and S0 interfaces so that the E0 receives the first usable subnet while the S0 receives the second usable subnet from the network 192.168.160.0/28. Both interfaces would receive the last available ip address on the proper subnet.
NotE. The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process.
Answer:
Explanation:
ROUTER
-M> enable PassworD. Cisco ROUTER-M# config t ROUTER-M(config)# interface e0 ROUTER-M(config-if)# ip address 192.168.160.14 255.255.255.240 ROUTER-M(config-if)# no shutdown ROUTER -M(config-if)# exit ROUTER -M(config)# interface s0 ROUTER-M(config-if)# ip address 192.168.160.30 255.255.255.240 ROUTER-M(config-if)# no shutdown ROUTER-M(config-if)# end ROUTER-M# copy run start
NEW QUESTION 48
In the configuration of NAT, what does the keyword overload signify?
- A. The pool of IP addresses has been exhausted.
- B. Multiple internal hosts will use one IP address to access external network resources.
- C. If the number of available IP addresses is exceeded, excess traffic will use the specified address pool.
- D. When bandwidth is insufficient, some hosts will not be allowed to access network translation.
Answer: B
Explanation:
Explanation/Reference: http://evilrouters.net/2009/07/09/configuring-basic-nat-with-overloading/
Overloading (having multiple clients all NAT'd to the same IP address) is probably the most common implementation (especially for those of us who run NAT on a Cisco box at home!).
NEW QUESTION 49
A brand launches a new website and wants to encourage people to visit it. What should the brand select first to create the campaign?
- A. Automatic Placements
- B. The appropriate ad objective
- C. The right call to action for the audience
- D. Custom Audiences and Lookalike Audiences
- E. The right creative for the campaign
Answer: B
NEW QUESTION 50
Which metric indicates how efficiently a campaign achieved its ad objectives?
- A. Spend
- B. Cost
- C. Results
- D. Cost Per Result
Answer: D
NEW QUESTION 51
After years of advertising on TV, a branding advertiser wants to start running ads on the Facebook App. The advertiser has a TV ad with an emotional message to connect the brand with customers The TV ad lasts 30 seconds.
What is the best creative approach to run this campaign?
- A. Create a 20 second video ad with a shorter version of the content used on TV
- B. Create a video ad with the content used on TV
- C. Create a 15-second video ad with the content used on TV
- D. Create a 15-second video ad that is vertical with the content used on TV
Answer: C
NEW QUESTION 52
What is the purpose of flow control?
- A. To reassemble segments in the correct order at the destination device.
- B. To regulate the size of each segment.
- C. To ensure data is retransmitted if an acknowledgement is not received.
- D. To provide a means for the receiver to govern the amount of data sent by the sender.
Answer: D
Explanation:
Explanation/Reference: http://whatis.techtarget.com/definition/flow-control Flow control is the management of data flow between computers or devices or between nodes in a network so that the data can be handled at an efficient pace. Too much data arriving before a device can handle it causes data overflow, meaning the data is either lost or must be retransmitted. For serial data transmission locally or in a network, the Xon/Xoff protocol can be used. For modem connections, either Xon/Xoff or CTS/RTS (Clear to Send/Ready to Send) commands can be used to control data flow. In a network, flow control can also be applied by refusing additional device connections until the flow of traffic has subsided.
NEW QUESTION 53
Refer to the exhibit.
Host A can communicate with Host B but not with Hosts C or D. How can the network administrator solve this problem?
- A. Install a router and configure a route to route between VLANs 2 and 3.
- B. Enable the VLAN trunking protocol on the switch.
- C. Install a second switch and put Hosts C and D on that switch while Hosts A and B remain on the original switch.
- D. Configure Hosts C and D with IP addresses in the 192.168.2.0 network.
Answer: A
Explanation:
Explanation/Reference: Two VLANs require a router in between otherwise they cannot communicate through a simple switch mechanism
NEW QUESTION 54
What are two benefits of the interconnectivity of the Meta products? (Choose 2)
- A. Manage ad campaigns across platforms from one interface
- B. Apply reach and frequency across Messenger
- C. Divide budget by platform
- D. Optimize ad campaigns by placement type
Answer: D
NEW QUESTION 55
Refer to the exhibit.
Assume that all router interfaces are operational and correctly configured. In addition, assume that OSPF has been correctly configured on router R2. How will the default route configured on R1 affect the operation of R2?
- A. Any packet destined for a network that is not directly connected to router R1 will be dropped.
- B. The networks directly connected to router R2 will not be able to communicate with the 172.16.100.0, 172.16.100.128, and 172.16.100.64 subnetworks.
- C. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately.
- D. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1.
- E. Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur.
Answer: E
Explanation:
First, notice that the more-specific routes will always be favored over less-specific routes regardless of the administrative distance set for a protocol. In this case, because we use OSPF for three networks (172.16.100.0 0.0.0.3, 172.16.100.64 0.0.0.63, 172.16.100.128 0.0.0.31) so the packets destined for these networks will not be affected by the default route. The default route configured on R1 "ip route 0.0.0.0 0.0.0.0 serial0/0 will send any packet whose destination network is not referenced in the routing table of router R1 to R2, it doesn't drop anything. These routes are declared in R1 and the question says that "OSPF has been correctly configured on router R2, so network directly connected to router R2 can
communicate with those three subnetworks.
As said above, the default route configured on R1 will send any packet destined for a
network that is not referenced in its routing table to R2; R2 in turn sends it to R1 because it
is the only way and a routing loop will occur.
NEW QUESTION 56
What two things does a router do when it forwards a packet? (Choose two.)
- A. computes the destination host address
- B. switches the packet to the appropriate outgoing interfaces
- C. updates the destination IP address
- D. forwards ARP requests
- E. determines the next hop on the path
Answer: B,E
Explanation:
Without following these two processes namely switching the packet to appropriate interface and telling the packet where to go by providing it with a destination IP address, the purpose of the same would not be solved.
NEW QUESTION 57
Refer to the exhibit.
The two routers have had their startup configurations cleared and have been restarted. At a minimum, what must the administrator do to enable CDP to exchange information between
R1 and R2?
- A. Configure IP addressing and no shutdown commands on either of the R1 or R2 fa0/1 interfaces.
- B. Configure IP addressing and no shutdown commands on both the R1 and R2 fa0/1 interfaces.
- C. Configure the router with the cdp enable command.
- D. Enter no shutdown commands on the R1 and R2 fa0/1 interfaces.
Answer: D
Explanation:
Explanation/Reference:
If the shut down commands are not entered, then CDP can exchange information between
the two routers, else it would fail.
NEW QUESTION 58
Which two of these functions do routers perform on packets? (Choose two.)
- A. Examine the Layer 3 headers of inbound packets and use that information to determine the complete paths along which the packets will be routed to their ultimate destinations
- B. Examine the Layer 2 headers of inbound packets and use that information to determine the next hops for the packets
- C. Update the Layer 3 headers of outbound packets so that the packets are properly directed to their ultimate destinations
- D. Update the Layer 2 headers of outbound packets with the MAC addresses of the next hops
- E. Examine the Layer 3 headers of inbound packets and use that information to determine the next hops for the packets
- F. Update the Layer 3 headers of outbound packets so that the packets are properly directed to valid next hops
Answer: D,E
Explanation:
Explanation/Reference:
This is the basic function of the router to receive incoming packets and then forward them
to their required destination. This is done by reading layer 3 headers of inbound packets
and update the info to layer 2 for further hopping.
NEW QUESTION 59
What is a valid reason that an ad would be rejected by Facebook?
- A. An image within the ad was relevant to its message
- B. The ad contained sexually suggestive images.
- C. The link to the landing pages included content that was relevant to the ad
- D. Lead ads were used to receive email, first name and phone number
Answer: B
NEW QUESTION 60
......
Updated Test Engine to Practice 100-101 Dumps & Practice Exam: https://examcollection.vcetorrent.com/100-101-valid-vce-torrent.html